SPA OWNER RESOURCES

Use these resources to learn more about your spa.


 

Troubleshooting Procedures for 880 Series

In the unlikely event your spa is not working in the way you believe it should, please first review all the installation and operating instructions in this manual, and check the message on the panel display; second, if you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions.

None of the components operate (i.e. pump, blower, light)

Check the control panel lights
  • If there are letters or symbols displayed on the screen, refer to the previous section to determine meaning and action required.
  • If nothing appears on the screen:
    • Check the household circuit breaker.
    • Contact your Sundance Spas dealer or qualified service technician.

Pump does not operate and icon does

Depress JETS Button
  • If no sound is detected or if a buzzing sound is detected, turn off power to the spa and contact your authorized dealer or qualified service technician
  • If motor operates, but now water flows to jets:
    • Pump may not be properly primed. See instructions below.
    • Contact your Sundance Spas dealer or qualified service technician.

Pump Priming Instructions

This method must be used for the jets pumps because these pumps are not connected to the main filter system in any way.
  • Turn off the power to the spa.
  • Remove the handle from the massage selector supplied by the pump you are priming.
  • Loosen the massage selector's cap slightly (counterclockwise), listening for the air to seep out.
  • Tighten the cap finger tight, replace the handle, and turn the spa's power back on.
CAUTION: If freezing conditions exist and pump is not operational, take measures to protect​ the system from freeze damage. See Section title 'Winterzing', page 66.

Poor jet action (Sections 9.4-9, 25, pages 24-45)

Procedure:
  • Make certain the jets pump is turned on.
  • Check position of massage selectors
  • Open air control for selected jet system.
  • Check for adequate water level.
  • Check for dirty filter (pages 60-62)

Water is too hot

Procedure:
  • Reduce thermostat setting.
  • Switch spa to 'Economy' mode to turn heater on only during programmed filter cycles (page 54).

No heat

Procedure:
  • Check thermostat setting.
  • Keep the cover in place while heating.
  • If 'heater on' indictor is lit but no temperature rise is experienced after a reasonable period of time, contact your Sundance Spas dealer or qualified service technician.

Filter/circulation pump off

Procedure:
  • Verify filter/circulation pump is programmed to run 8 hours a day (page 54).
  • Filter/circulation pump cycle canceled by power interruption. Wait 24 hours for spa to reset or press select button for manual activation.
  • spa water is warmer than 95°F (35°C) and two degrees warmer than the set temperature. The 'Summer Logic' safety feature has activated. See not on page 55 for details.

Should checking the above steps fail to correct the problem, please call your authorized dealer so that he may arrange service. We are always striving to improve the quality and features of our products. Your input as a spa owner is a cherished part of this process. If you have any comments or suggestions, or if you wish to be informed on any new products for your spa, please write to us. Congratulations on your good taste and welcome to the happiest and most relaxed family in the world!

Camp Hill

3501 Simpson Ferry Rd.
Camp Hill, PA 17011
717-763-8118

VIEW DETAILS

Carlisle

40 Noble Blvd.
Carlisle, PA 17013
717-422-5577

VIEW DETAILS

Harrisburg

5207 Jonestown Rd.
Harrisburg, PA 17112
717-657-8877

VIEW DETAILS

Lancaster

1637 Manheim Pike
Lancaster, PA 17601
717-509-7946

VIEW DETAILS

Lebanon

717 Quentin Rd.
Lebanon, PA 17042
717-270-0477

VIEW DETAILS

Service Department

717-774-6613

Find us online